Do I need airbag module reset?

MyAirbags-Airbag-Module-Airbag-Reset-Mazda3-Mazda6-2013-2014-2015-2016.jpg

After a vehicle has been in an accident, airbag control module needs to be reset in order to be used again.

Our services are an alternative to dealership expensive part replacement. The dealer and/or scan tools will not be able to clear hard code due to hardware issues and will offer to sell you a new replacement airbag module that usually cost around $180 to $600 depending on the vehicle.

We can reset airbag module back to its original manufacturer state. After we reset your module, you will not need to take it to the dealer for any additional programming. When you receive the module back from us it will be as good as new. Almost all airbag modules can be reset, except if they are flood or fire damaged. It is always best to send your original module to us for reset to avoid additional trip to the dealer for coding. Most of the late model cars will have partial VIN stored in the airbag control module. Our service is 100% guaranteed or your money back. 

Airbag Module Reset & Return (Like New, Only Better)

your original module is reset and will not need to be coded to your vehicle VIN, since it is original and came out of your vehicle

Dealership told you that you need a new module?

We reset all fault codes. After you receive the module from us you will not have to take it to the dealer for any additional programming. All airbag control modules can be reset and reprogrammed, except if flood, fire or hardware damage.

Even after small accident codes will be stored in the module.

This is a Reset and Return service of your existing Airbag Control Module. You will need to remove and send your module to us for reset. We reset all fault codes. After you receive the module from us you will not have to take it to the dealer for any additional programming. All airbag control modules can be reset and reprogrammed, except if flood, fire or hardware damage.

Reset airbag module codes at MyAirbags

It is crucial to have your vehicle’s airbags replaced or airbag module reset following an accident. Many car dealerships must place special orders to replace airbag modules, which greatly increases the replacement cost. At MyAirbags, we can reset your original airbag control module.

It is always better to have your airbag control module reset, because when you get it back it is the original module and will not need additional programming from the dealer. If you purchase a new or used module you will need to make sure the part number is the same and then you may need to take it to the dealership to have it programmed to your vehicle. That is why if you send the original module and then have MyAirbags reset it for you, it is the same unit going back in the same vehicle and no programming needed.

Accessing the vehicle’s airbag control module

To ensure your safety when removing and installing your airbag module, MyAirbags provides these simple tips:

Removing the Airbag Module

  1. Disconnect the positive lead on the battery and wait three minutes
  2. Locate the SRS computer module, which is often located directly below the center console between the front two seats. In GM vehicles, the SRS computer module is typically found under either the driver or passenger seat, while in other vehicles it may be found near the floor in the center of the dash.

Installing the Airbag Module

  1. Ensure proper connections of all SRS components, including clock springs, airbags, impact sensors and seat belts.
  2. Disconnect the battery cables, and carefully insert the reset airbag control module.
  3. Connect the airbag control module wiring plugs. Make sure module is bolted down. If not bolted down the airbags and seat belts may deploy
  4. Re-connect the battery after securing the airbag module.

All vehicles available for airbag control module reset

High quality, cost-effective solutions at MyAirbags provide airbag control module resets for all vehicle makes and models from 1995 and up.

Contact us

No need to replace your airbag control module unless it has been in water flood or fire damage. Send your original module to us for reset and save hundreds!

Call us 678-778-8890 or submit a request  to learn more about our airbag module reset service.

Start your order today!

Here is a sample what an airbag control module looks like

 MyAirbags-Airbag-Module-Airbag-Reset-GMC-Chevy-Buick-Cadillac-2007-2010.jpgMyAirbags-Airbag-Module-Airbag-Reset-GMC-Chevy-Buick-Cadillac-2010-2017.jpgMyAirbags-Airbag-Module-Airbag-Reset-Ford-Lincoln-1.jpg MyAirbags-Airbag-Module-Airbag-Reset-Dodge-Chrysler-Jeep-1.jpg 

Was this article helpful?
1 out of 1 found this helpful
Have more questions? Submit a request

Comments

Please sign in to leave a comment.